PRODUCT USE & CARE INSTRUCTIONS

Apply
THE KORA
CLEANING
REMOVE & REAPPLY

- QUICK & EASY APPLICATION -

APPLICATION INSTRUCTIONS

  1. Locate and prepare a suitable surface for your Konsilee product.
  2. Give the surface a wipe over with isopropyl alcohol.
  3. Ensure the surface you are applying your product to is clean and free from any cleaning chemicals.
  4. Ensure the surface is completely dry before attempting to apply the product.
  5. Remove the backing film and place the product on your desired surface, ensuring to apply it in a diagonal direction, from one corner to the other, to minimise air bubbles from forming. 
  6. Important: Leave the product to sit empty and dry for at least 12 hours before use.
  7. You can test the product by applying some downwards pressure to the pocket of the product to ensure it has sufficiently attached to the surface it has been applied to. 
  8. If your surface has calcium present, ensure to completely clean/remove the calcium build-up from the surface prior to applying our holders. 

Important Notes:

Do not apply water to the contact surface prior to product application, as this will not allow the product to properly attach. 

Do not apply products over any grout lines.

Do not overload the product.

Konsilee products are not suitable to store breakable items, such as glass.

Konsilee items are waterproof and have drainage holes, however, they should be cleaned when necessary to ensure cleanliness is maintained. 

THE KORA CORNER CADDY

APPLICATION INSTRUCTIONS

  1. Ensure the surface you are applying your product to is clean and free from any cleaning chemicals.
  2. Give the surface a wipe over with isopropyl alcohol.
  3. Ensure the surface is completely dry before attempting to apply the product.
  4. Hold the caddy up to the corner and position it where you would like it to sit. Take a moment here to line it up, it must be applied straight and level.
  5. Remove one side's backing film and place the opposite side against the wall, slightly out from the corner.
  6. Slide the product straight along the surface, towards the corner softly. Stop once the product first touches the wall.
  7. Check the product has been applied straight, then firmly press all adhesive areas on this side against the wall, ensuring full contact has been made with the surface. Note: Do not push the corner of the caddy tightly into the corner. The design is slightly rounded and is intended to sit just off the corner, not forced into it.
  8. Remove the film from the opposite side, then firmly press this side against the wall, working from the innermost part, outwards.
  9. Important: Leave the product to sit empty and dry for at least 12 hours before use.

Extra Information & Tips:

Our corner caddies are designed without adhesive in the centre corner section, meaning this corner area (only) can sit over the single vertical corner grout line. No other area of the caddy is permitted to be placed over any other grout lines.

You may wish to position the caddy just above a horizontal grout line to help guide a straight, level application.

If this isn't an option, you're welcome to fold an A4 sheet of paper in half and place the folded edge into the corner of your shower, where you intend the bottom of your caddy to sit. Secure it in place with tape or Blu Tack, then apply the caddy directly above the paper, using the straight edge as a guide to ensure the base of the caddy is level.

Button label

- EASY TO CLEAN -

PRODUCT CLEANING & CARE

Silicone Cleaning: Use a soft microfibre cloth along with warm, soapy water to clean the silicone of your product/s. Be sure to clean the product pouches, drainage holes, and the inner silicone recess of the shower mirror.

Shower Mirror: Rinse shower mirror with water only, when needed. Do not use cleaning products or cloths to clean the mirror surface, as this can compromise the mirror's surface and fog-resistant coating.

IMPORTANT: Do not use abrasive pads, brushes, or chemical cleaning agents on any of the products, as this may cause damage to the surface and overall appearance.

Product Care 

Clean your products regularly using the above directions, to maintain cleanliness.

Please ensure to use and install our products as directed, as failure to do so can result in the product not functioning as intended. 

Not using the product as directed can result in damage to the product or the items being held within the product. 

Please take care when applying the product by ensuring the area is completely dry, to ensure injury does not occur. 

Button label

- INSTRUCTIONS -

Remove & Reapply

REMOVE:

With clean hands, gently peel the product and adhesive away from the wall as one unit. Ensure you have hold of both the silicone and adhesive film before you begin. Do not peel the silicone alone, as this may cause irreversible damage by separating the adhesive from the silicone.

STORE:

If you are moving house, cover the adhesive film with baking paper whilst it is not applied to a surface. Store carefully to ensure the adhesive does not become dirty or damaged.

REAPPLY:

  1. If the adhesive is clean and dry, skip to step 2. If it is wet, or if there is any dust, dirt, or hair present, rinse the adhesive side under running water and gently clean with your hand. The water will temporarily make the adhesive feel completely slippery.
  2. Place the product in a safe, clean area with the adhesive side facing upward and allow it to air dry completely overnight (or for at least 12 hours). The adhesive's tackiness will return as it dries.
  3. Firmly reapply your product/s to a compatible surface following our application instructions.
  4. Leave the product empty with no weight added for at least 12 hours — this is essential for a strong bond.

Please Note: The adhesive and surface must be completely dry before reapplying. Refer to our application page for full instructions.

- QUICK, EASY APPLICATION -

APPLICATION INSTRUCTIONS

  1. Locate and prepare a suitable surface for your Konsilee product.
  2. Give the surface a wipe over with isopropyl alcohol.
  3. Ensure the surface you are applying your product to is clean and free from any cleaning chemicals.
  4. Ensure the surface is completely dry before attempting to apply the product.
  5. Remove the backing film and place the product on your desired surface, ensuring to apply it in a diagonal direction, from one corner to the other, to minimise air bubbles from forming. 
  6. Important: Leave the product to sit empty and dry for at least 12 hours before use.
  7. You can test the product by applying some downwards pressure to the pocket of the product to ensure it has sufficiently attached to the surface it has been applied to. 
  8. If your surface has calcium present, ensure to completely clean/remove the calcium build-up from the surface prior to applying our holders. 

Important Notes:

Do not apply water to the contact surface prior to product application.

Do not apply products over any grout lines.

Do not overload the product.

Konsilee products are not suitable to store breakable items, such as glass.

Konsilee items are waterproof and have drainage holes, however, they should be cleaned when necessary to ensure cleanliness is maintained. 

- APPLICATION INSTRUCTIONS -

THE KORA | CORNER CADDY

  1. Ensure the surface you are applying your product to is clean and free from any cleaning chemicals.
  2. Give the surface a wipe over with isopropyl alcohol.
  3. Ensure the surface is completely dry before attempting to apply the product.
  4. Hold the caddy up to the corner and position it where you would like it to sit. Take a moment here to line it up, it must be applied straight and level.
  5. Remove one side's backing film and place the opposite side against the wall, slightly out from the corner.
  6. Slide the product straight along the surface, towards the corner softly. Stop once the product first touches the wall.
  7. Check the product has been applied straight, then firmly press all adhesive areas on this side against the wall, ensuring full contact has been made with the surface. Note: Do not push the corner of the caddy tightly into the corner. The design is slightly rounded and is intended to sit just off the corner, not forced into it.
  8. Remove the film from the opposite side, then firmly press this side against the wall, working from the innermost part, outwards.
  9. Important: Leave the product to sit empty and dry for at least 12 hours before use.

Extra Information & Tips:

Our corner caddies are designed without adhesive in the centre corner section, meaning this corner area (only) can sit over the single vertical corner grout line. No other area of the caddy is permitted to be placed over any other grout lines.

You may wish to position the caddy just above a horizontal grout line to help guide a straight, level application.

If this isn't an option, you're welcome to fold an A4 sheet of paper in half and place the folded edge into the corner of your shower, where you intend the bottom of your caddy to sit. Secure it in place with tape or Blu Tack, then apply the caddy directly above the paper, using the straight edge as a guide to ensure the base of the caddy is level.

- EASY TO CLEAN -

PRODUCT CLEANING & CARE

Silicone Cleaning: Use a soft microfibre cloth along with warm, soapy water to clean the silicone of your product/s. Be sure to clean the product pouches, drainage holes, and the inner silicone recess of the shower mirror.

Shower Mirror: Rinse shower mirror with water only, when needed. Do not use cleaning products or cloths to clean the mirror surface, as this can compromise the mirror's surface and fog-resistant coating.

IMPORTANT: Do not use abrasive pads, brushes, or chemical cleaning agents on any of the products, as this may cause damage to the surface and overall appearance.

Product Care 

Clean your products regularly using the above directions, to maintain cleanliness.

Please ensure to use and install our products as directed, as failure to do so can result in the product not functioning as intended. 

Not using the product as directed can result in damage to the product or the items being held within the product. 

Please take care when applying the product by ensuring the area is completely dry, to ensure injury does not occur. 

It is not recommended to use coloured/pigmented soaps, cosmetics or personal care products on silicone surfaces, as permanent staining may occur. Use of pigmented products is at your own discretion.

Do not separate or remove the adhesive from the silicone. The adhesive is permanently affixed during manufacturing and cannot be replaced once removed.